The owner of a private house needs to consider many factors from the very beginning of construction to the complete availability of housing. If you have your own home, then you probably came across a situation where you had to plan or redo communications. An important point can be missed even when working with the master. For example, frozen condensate in ventilation in a private house or on the roof of the MKD will soon weaken the draft, until the air exchange stops completely.
In the cold season, moisture can collect in excess and destroy materials. Ventilation in a large house can not be redone in one day, but thanks to the article you will learn all the nuances and will be ready for repair. You will not make mistakes, save time and money. We will talk about the features of condensate and methods for its elimination.
Condensation forms during mechanical problems with ventilation and certain external conditions. There are many options for how to get rid of it, and three ways with a more thorough approach. From the article you will understand which method will be more convenient and justified for you.
Causes of condensation
Condensation occurs due to external factors, with poor ventilation. Installers sometimes make mistakes and the system works poorly. Condensation also builds up due to increased humidity in the house.
Drops on the inside of the windows will indicate excessive humidity in the room. In summer, only frequent ventilation is needed, and there will be no moisture in the pipes. In cool time, the air liquefies on the walls of the air channels, primarily at the junction of heat and cold.
In the cold season, the condensate in the head freezes and turns into icicles. It will have to be removed from the pipe with a stick or manually
Other causes of condensation:
- leakage of ventilation;
- destruction of the pipe from the side of the street;
- the proximity of the channels to the external wall;
- the pipes were not insulated;
- insufficient wall insulation;
- temperature differences in the building / on the street;
- icing at home;
- basement water;
- the house was built on a wet foundation;
- there is a leak in the water supply.
Condensate ventilation ducts will gradually fill harmful microorganisms. It will be difficult to remove them from there, and in addition there will be an unpleasant smell and the likelihood of getting sick.
Ventilation pipes need to be cleaned. Insects, spiders, leaves get there. Birds erect nests in the conclusions. Due to weakening traction, more condensate forms. It does not hurt to check the strength of the inflow / outflow of air with a sheet of paper or a lit match. Improper circulation also reduces traction.
In winter, the outdoor outlet can completely freeze, and if you do not control this moment, there will be excess moisture on the walls and ceilings, and the finish will deteriorate.
Condensation is also caused by large bodies of water nearby. Sometimes the residents themselves are to blame - if they dry their clothes indoors.
How to get rid of condensation in ventilation?
Condensation is the conversion of gas or saturated vapor into moisture. Sometimes this is called the transformation immediately into a solid (desublimation). In severe frost, moisture near the head of the ventilation quickly turns into ice.
The picture shows a classic drawing of ventilation of a private house: a short duct on the roof, thermal insulation above the ceiling of the upper residential floor, condensate drainage to the basement - this has both pros and cons
Residents of private buildings are easier to solve the problem: it is easier to find the necessary conclusions, nobody forbids changing the ventilation, and special permissions are not needed. Thanks to the new ventilation pipes, condensate in private houses appears later than in old high-rise buildings, under the same conditions.
In the case of low traffic, the channels are cleaned with a pipe brush. When depressurization will have to look for a hole. Humidity rises due to unbalanced air exchange. In private houses there are more rooms, and a powerful ventilation system should be laid. If it already works, and replacement is undesirable or difficult, it remains to stimulate the removal of moist air and the flow of fresh instead.
The complete absence of moisture and frost in the ventilation and a stable result give three methods:
- Reliable thermal insulation (insulation).
- Forced ventilation
- Changing the pattern of the external duct - to drain moisture into the condensate collector.
With the second and third methods, thermal insulation will bring additional benefits. Keep in mind that with the first and third options you need to work with all organized natural ventilation: its supply, exhaust and supply and exhaust routes.
At the design stage, there is a choice: buy pipe sandwiches with a layer of insulation under the top coating or purchase insulation for individual parts. Now there are many materials that exactly repeat the bends of the ventilation elements - crosspieces, tees and others
Sometimes it is necessary to change damaged or old ventilation elements. In the worst case, be prepared to install the new system and plug the old one. The problem cannot be ignored if there is always a lot of moisture in the attic.
Method # 1. Correct and high-quality thermal insulation
Warming is primarily in places with the largest temperature difference. The channels near the ceiling of the upper floor, in the attic and roof need insulation. They are insulated in exactly this order, and then they are insulated below, if temperature contrast is also possible there.
Supply systems ideally isolate not only through pipes, but also through valves. After arranging the problematic part of ventilation, it will be possible to save on the rest.
Such heaters are suitable:
- polyethylene foam;
- polypropylene;
- expanded polystyrene;
- mineral wool;
- glass wool.
Mineral wool reliably protects from the cold, but quickly deteriorates from moisture and partially loses its properties. Only a layer of waterproofing will help. Glass wool is stronger than the usual mineral, but otherwise almost the same.
In polyethylene foam, good moisture resistance, low weight are noted. Similar qualities are observed in polypropylene. Foamed polystyrene (expanded polystyrene) almost does not let steam through, which is considered a plus in modern design for heat retention.
Mineral wool should be pre-cleaned of dirt, impurities and rust, then fixed with glue, tape and screeds and coated with roofing material or glassine on top to protect against moisture
Phased pipe insulation:
- We wipe the channels, remove all moisture.
- We wind heat-insulating material on pipes. We start with the channels of the top of the building and problem areas. We fix it with tape. We lay the adhesive tape longitudinally and additionally wrap it with transverse segments with a small interval.
- We achieve maximum tightness at the joints of the insulation and pipes.
- For channels with a circular cross section, cylindrical seals are also suitable. Cut them on one side. Then we glue and fix with tape.
- Do not leave clearance with air. Condensation may also form there, and it will ruin the thermal insulation. This will also lead to corrosion.
The distance between some pipes is inconvenient for insulation, so it is closed up. Suspended formwork is installed there, after which the space is filled with cement mortar.In places where ventilation goes behind the brickwork, it is worth denser to seal the seams, isolate cracks. The above does not fully protect against cold, but the main thing is that cold air will not fit the pipes and will not cause condensation.
After proper work, the dew point will move outside the ventilation range. And as soon as you eliminate the condensation, the humidity will drop dramatically: in the case of ventilation of a private house, the changes will be significant - up to 60% or less.
Do not insulate narrow corrugated pipes from ductile metals. They are replaced with plastic ones.
Warming will simultaneously solve other issues. Fire safety will increase. Heat losses will decrease. The owners will not be disturbed by noise in the ventilation ducts.
Fill any joints and cracks in the upper part of the house, apply the funds gradually in several layers and use small diameter nozzles
The thickness of the insulation should be selected based on all the needs at once. To get rid of condensate guaranteed, the external part of the ventilation is protected by a heater with a thickness of 50 mm, or better - from 100 mm. The head of the pipe is equipped with a deflector.
Method # 2. Forced ventilation
Its arrangement begins with the kitchen. An exhaust fan is installed there. Old natural ventilation is left or blanked. A new device is sometimes mounted in a window cloth, instead of a window leaf or a large sash.
An option for an exhaust system in a wall or pipe going out of the room to the street may be more comfortable. An outlet hole is made either far from the outer part of the chimney, or slightly lower.
An exhaust system from the side of the street is equipped with check valves. Instruments look like nozzles. There is a flat version with a film partition. The film bends outward and lets warm air out of the house, but does not allow cold to enter even in strong winds.
There are valves with a plastic partition, which scrolls slightly along its axis, but only when exposed from the inside. With a greater thickness, such a device is less leakproof.
The supply valve above the battery is placed so that the center of the street hole is 60-80 millimeters above it and just below the window sill
For intake of air from the street, a supply valve is organized. It is placed next to a battery or other heating element and adjusted if necessary. The house will still be warm, and almost all the condensate will be able to be taken from the ventilation.
The best material for an external forced ventilation pipe is considered plastic.
Method # 3. Changing the pattern of the outdoor duct
Consider the option where the external part of the ventilation leaves the building horizontally and has a bend up. Then the ventilation pipe is separated at the bend. Necessarily at the lowest point - consider this if the drawing is more complex.
In the resulting hole, fix the tee. A sawed-off part is placed in the upper pipe, and the lower one is closed with a plug cone (condensate collector). Draining condensate will come out through it. In another way, this method is called condensate drain. The resulting system is insulated. This reduces the likelihood of freezing of the outlet during prolonged frost.
On the condensate collector, you can fix the tube to drain the liquid, and send the free end into the bucket. This is done if the collection is in an inaccessible place. Sometimes they manage with only one bucket or organize a drain into the sewer. With a moderate amount of moisture, absorbent material is placed in the filtration zone. The cassette with it often has to be removed and dried.
The option of placing the condensate collector on a bent pipe without installing a tee. This is only permissible with the outlet channel tilted down and at the lowest point
The conical shape of the plug has an advantage over a flat one, in which water stands and almost does not leak, despite the holes. The liquid from the latter is drained by hand.
In winter, the situation changes a little - icicles appear and on a cone they cover a large area. Air from the house heats the ice a few days after a severe frost, and they fall. The length of the lower pipe of the tee is enough so that during this time the water does not reach the level of branching. Watch for the formation of ice and, if necessary, knock it yourself with a stick.
In a house with ventilation that has not yet been laid or not completely finished, it makes sense to make a side exit through the pediment. The task for self-laying will become easier than the idea of drilling a hole in the roof slope. Do not use this option if the pipe extends far from the pediment.
Diagram of a pipe with several bends and a tee for removing moisture, which is useful for houses with large eaves overhangs
Bending with a long channel after it will significantly reduce traction. On the other hand, the rooms below will get better protection against moisture.
If the outer part of the ventilation goes only horizontally, then you can crash into it in any area. In a strictly vertical pipe, as well as in a curved one, they search for a lower point. From a smooth vertical channel, the drain usually goes inside the house.
Insulation ventilation with mineral wool in order to eliminate moisture is a good example:
Sewer pipe in the role of ventilation, with a special channel for condensate:
Excessive humidity in ventilation is eliminated in several ways. To do this, repair and clean the pipes, insulate them or install an additional ventilation system. If you live in a private house, then to remove condensate from the ventilation, you can somehow change the structure of the pipes. Sometimes the system is completely redone, replaced with a new one. If in your case there were few negative factors, then the state of ventilation will allow it to be maintained.
Ask questions and write comments about ventilation in your home. Tell us about her condition, effectiveness. Perhaps your information will be of interest to other users. The contact form is located below.